Home > Hard Drive > Swap IDE Hard Drive With Another IDE Hard Drive

Swap IDE Hard Drive With Another IDE Hard Drive

Contents

Each 40 pin connector corresponds to one IDE channel, and the connectors are next to the single 34 pin floppy cable socket. Keep in mind that 2.5-inch enclosures are usually bus powered, meaning that they pull power from the port they’re plugged into and they don’t come with a power adapter; this makes All submitted content is subject to our Terms of Use. Just take whichever tools you need from the toolset to USB-connect your drive and power it. (The toolset does not include a drive enclosure, so you'll want to buy that separately have a peek at this web-site

by R. when I type in setup and my cd-rom drive prompt, a message comes up that says windows is needed to run that program. Andrew SME 82,618 views 5:02 Make money with Hard Drives - Duration: 8:51. It still takes a while, but it's faster than a separate partition, format and copy routine, and you don't have to be there until it finishes. http://www.makeuseof.com/tag/install-ide-hard-drive/

Ide Hard Drive Jumper Settings

If you copy a whole drive, Windows may even work just fine on the copied drive. There will be a diagram somewhere. I already bought the adapter so I'm going to give it a try, i also ordered the SATA data cable considering the power cable is already provided along with the IDE But there are a few nasty surprises that might spoil your smooth swap operation, and DOS and Windows by themselves are insufficient to do the job properly.

  • Discussion topics include SSD, SATA drives, USB drives, external hard drives, RAID arrays, backup, IDE drives, network attached storage (NAS), thumbdrives, Western Digital, Kingston, LaCie, and SanDisk.Real-Time ActivityMy Tracked DiscussionsFAQsPoliciesModerators Question
  • But Windows, at its lower levels, certainly does.
  • Ihave tried to install the drivers from the SATA PCI card but it tells me there are no divice drivers were found, make sure the media contains the correct drivers &

Since I am moving to the Dell will there still be a BIOS that I can set the IDE drive as the boot drive? I've tried everything I've contacted Seagate but they told me the warranty is only it HD stops working.. SSHD: The Future of Hard Drives? Seagate Ide Hard Drive Jumper Settings We won’t get into the details of upgrading a hard drive because it’s a very complicated process.

How much degradation you experience depends on the patterns of your disk use and which IDE standards are involved. (I exclude these complexities here.) For typical office work this configuration works Since my IDE Drive has an OEM version of XP (and a different flavor of XP) will it need to be reactivated, and infact will MS activate XP anymore?4. If there are two devices, the controller on one of them handles both. http://www.howtogeek.com/182452/how-to-get-data-off-an-old-hard-drive-without-putting-it-in-a-pc/ Thanks reply quote 1 year agoGeoffrey N.

It is a boot drive, if I put it in an enclosure and make it an external drive, would it work then? How Many Hard Drives Can Be Connected To A Single Ide Cable The hard disk is similar, but this time I chose “Master with Slave Present“. Flag Permalink Reply This was helpful (0) Collapse - So the adapter wouldn't work? You need to buy a hard-drive enclosure that matches the size of the drive you have; a 2.5-inch enclosure for a 2.5-inch drive and a 3.5-inch enclosure for a 3.5-inch drive.

How To Connect Ide Hard Drive To Motherboard

It's possible for that setting to be determined by "cable select", but you need a special cable to do that which practically nobody bothers to use, and you still need to http://www.geek.com/forums/topic/can-i-swap-my-hard-drive-with-operating-system-to-another-motherboard/ Will the enclosure allow me to transfer through a USB port on my Hp  Laptop are all cables included? Ide Hard Drive Jumper Settings Drive enclosure for permanent use. How To Connect Ide Hard Drive To Sata Motherboard by AdamJalal91 / May 5, 2016 5:37 PM PDT In reply to: Back to Speco.

These are now widely available and a lot cheaper than the one you bought years ago.Maybe you can drop the camera count to say 4 on this old one and get Check This Out My brain is small.The OP wants to use the OS of one brand to another. I want to make my new hard drive the C:/ drive. Current consumer SCSI controllers all do automatic termination, so you don't have to worry about their end of the chain. How To Install Ide Hard Drive

Logged quaxoGuru What, me worry?Thanked: 127 Computer: Specs Experience: Expert OS: Windows 7 Re: How to swap a IDE hard drive from a Gateway to a Dell the has a SATA Today, 99 bucks for 4 camera unit sans HDD which runs about 99 bucks.I run into folk that want to milk the old DVR forever so I understand that. Unfortunately some are flimsy or have poor quality control. http://placedroid.com/hard-drive/the-hard-drive.html We also taught you all about partitions How To Set Up A Second Hard Drive In Windows: Partitioning How To Set Up A Second Hard Drive In Windows: Partitioning Read More

I can't load the cctv forums their website is down or something. How To Connect Two Hard Disk In One Pc If software recovery fails, you may need to consult with a local service center for more in depth recovery options.   reply quote 9 months agoDethcow Can an old HDD be You must first boot from an alternate drive.

CyberTech 187,950 views 2:02 Modifying a PATA to SATA Power Cable - Duration: 4:45.

But if i was trying to use the computer on a regular basis I would make sure I had the right drivers installed. *the OS on the drive was 98, but PATA SATA Next, you have to determine what kind of drive you have because you need an enclosure that’s compatible with your drive. Windows XP requires tapping the F6 key at a certain point during OS installation. Western Digital Ide Hard Drive Jumper Settings I am sorry but unfortunately B&H currently does not carry a scsi to usb adapter/enclosure.

CNET Reviews Best Products Appliances Audio Cameras Cars Networking Desktops Drones Headphones Laptops Phones Printers Software Smart Home Tablets TVs Virtual Reality Wearable Tech Web Hosting Forums News Apple Computers Deals Make sure you have the installation media (CD or downloaded file) for any programs you want to install on the new drive. Software driver. * Controller cards usually have a eSATA or USB port that allows external mounting. have a peek here A clean installation avoids copying corrupt or duplicate registry keys and other errors that tend to creep into any hard drive, but it takes a lot of time.

You used to be able to download a free functional trial version of Ghost, but Symantec don't link to it any more. Posted by: Bill 10 Oct 2010 Is it possible to keep the IDE hard drive with the operating system and use a PCI-compatible SATA host adapter card to connect a SATA Posted by: Jorge 07 Oct 2010 I´ve changed IDE drives for larger ones several times and it is an easy task. Proffitt Forum moderator / May 5, 2016 7:14 PM PDT In reply to: Thank What we need to do is to read the manual for this one.

Try to keep your CD-ROM either on a separate channel, or as a slave. 2. Also if you take a hard drive with Windows installed on it, out of one PC and put it into another PC, and set it to be the boot drive, it all fall short: they provide a cable but you're expected to provide the power via an old PSU or such. I believed that was a sign of impending failure.

The two machines have licensed XP versions, but the each can only be licensed nor its own maker. You can't put files on a drive until it's partitioned and formatted.