Home > Hard Drive > System Not Seeing Primary Slave Drive

System Not Seeing Primary Slave Drive

Contents

I am not sure what else to do to determine if it is bad. Does "Disk Operating System" imply that there was a "non-disk" Operating System? NOTE : This also occurs when you add a physical hard drive or CD ROM to the system when a persistent mapped network drive is setup for the user logging onto Thanks for the info. have a peek here

Thank you! Very helpful!! Well then, how can we fix or rebuild MBR without loading system? Can I use two 7805 ICs in parallel to get double current capacity? https://www.cnet.com/forums/discussions/primary-slave-drive-won-t-show-up-on-my-computer-19941/

Secondary Hard Drive Not Detected Windows 10

Good luck... -W 11 1/21/2007 (1:45 pm) by wkuagr wkuagr (328 Posts) I agree with Will. But then it just freezes up. Your blog saved the day. However, if fixing MBR still doesn't work, users need to try our last solution.

Your page sent me through the steps I needed and "I'm OK now" Thanks guys, I'll be back! It still has 2.79 GB of space used. So out of the 2 problems I has, one is fixed on the Dell for my Daughter. Internal Hard Disk Not Detected In Bios I plugged all three in and my computer screeched at me!!!!

Roberts on January 13, 2010 at 7:40 pm I run with windows 7 and use SATA HD When I installed a hard drive ( a have a couple of drives installed Play How the Game Should Be Played. Reply Cliff on December 11, 2008 at 3:23 pm Dave, Thank you for taking the time and making the effort to publish these instructions. http://www.tomshardware.com/forum/270832-32-sata-hard-drive-detected-bios-setup Finally, click "Apply" button to make all changes performed.

Please advise me physical installation, formatting and set partitions to the drive. Pata Hard Drives Are Older And Slower Than Sata Hard Drives. Disconnect the CDROM Drive and put in its place the offending hard drive (after making sure you have the pinout set to "Cable Select) You don't want anything but that one any suggestions. Register a free account to unlock additional features at BleepingComputer.com Welcome to BleepingComputer, a free community where people like yourself come together to discuss and learn how to use their computers.

Second Hard Drive Not Showing Up In Disk Management

what do i have to do to get the new c drive to work. try here Set it to cable select. Secondary Hard Drive Not Detected Windows 10 Could a Party Choose Not to Nominate an Incumbent? Second Hard Drive Not Detected In Bios I want to install it as a slave drive in my comp.

If I plug it into another IDE port while Windows is running, Windows shudders to a halt and hangs. navigate here right click on your installed drive and put it online first. However, if no normal computer is available, you'd better perform these operations: download a bootable partition manager to copy needed data, and then erase source data. Quickly Fix - The Disk Structure Is Corrupted and Unreadable Quick Recover Hard Disk Data from Lost or Damaged Partition Partition Software Version: MiniTool Partition Wizard Free Edition MiniTool partition Wizard Second Hard Disk Not Detected Windows 7

  • On IDE 1 I had the Hard Drive and on IDE2 I had the DVD as Master and CDR as Slave.
  • I was told by computer support group that I can only assign a letter once I installed the startup disk (which unfortunatley I couldn't find).
  • If that changes drive 'letters' then you need to adjust this in /etc/fstab.
  • Was this answer helpful?
  • I need you to tell me if the drive in question is SATA (one small black or red lead going to the motherboard and another similar to the power some way)
  • And the following 5 solutions are introduced in this order.
  • Helpful +2 Report Sabrina Sep 27, 2008 at 07:24 PM Okay then what do I do with the CD Rom???
  • Go through the appropriate prompts, making sure to select your older drive as the source and your newer one as the destination (pay careful attention to the hard drive sizes indicated
  • After I get it installed, I'll probably switch the drives around, or just set the boot priority to the slave. –Novicode May 21 '13 at 0:13 Okay well make
  • The tip on setting the jumper properly is what got my drive up and running.

The intent was just a secondary drive for extra space. Supposing the Missing Operating System error appears due to unsteady connection, the hard disk would appear in BIOS again after reconnection, and then Windows might be bootable. Sorry for the dumb question but is there really such a thing anyway?? http://placedroid.com/hard-drive/system-can-t-see-second-hard-drive.html Good luck to you for the future.

It sounds like i'm at least on the right path……Here is the exact log…Phoenix ROM BIOS PLUS Version 1.10 A05 Copyright 19854-1988 Phoenix Techmologies LTD. Not Recognizing External Hard Drive Reply curt on July 12, 2009 at 9:49 am You probably already figured it out…. To format the drive in Windows 2000 or XP, right-click on My Computer and go to "Manage".

Some of those drives get a five year period for this.

Open it up, copy your old files that you need (songs, pictures, documents...) to your new drive. Reply LUIS RESTO on June 24, 2009 at 11:06 pm DAVID YOU ARE THE BEST BROI want say Thanks so much for this postthis post help me alotthanks again DAVID RISLEY MiniTool Partition Wizard Bootable CD (freeware) can help do these operations. How To Detect New Hard Drive Windows 10 Wow again thank you Reply Eric on October 13, 2009 at 11:16 pm Great instructions.

This article tells how to build Free Bootable Partition Manager with Pwfree91.iso, follow the steps to create your own one. Plug your old hard drive into that IDE and power cable, making sure you set the jumper correctly. Reply Ryan O. http://placedroid.com/hard-drive/system-cant-see-new-seagate-120mb-drive.html Username Forum Password I've forgotten my password Remember me This is not recommended for shared computers Sign in anonymously Don't add me to the active users list Privacy Policy

TRENDING:

asked 3 years ago viewed 2121 times active 3 years ago Blog Podcast #103: Grandma, is that you? If a wrong partition is set active, naturally operating system cannot be found. I do have a suggestion though, could you add a few pics here and there so that we can see what you are talking about. I created a logical partition with PM which could then be seen by DOS and Windows.

You will see both a ribbon cable and a small power plug. Main Sections Technology News Reviews Features Product Finder Downloads Drivers Community TechSpot Forums Today's Posts Ask a Question News & Comments Useful Resources Best of the Best Must Reads Trending Now