Home > Terminal Server > Terminal Server And Cable Modem

Terminal Server And Cable Modem

Contents

You can always maintain connectivity to the terminal server and access the connected devices. A terminal server is a router with multiple, low speed, asynchronous ports that are connected to other serial devices, such as modems or console ports on routers or switches. Cabling The Cisco 2509 - 2512 series routers use a 68-pin connector and breakout cable. This document shows how to configure a terminal server to access only the console ports on other routers using Reverse Telnet. his comment is here

Configure In this section, you are presented with the information to configure the features described in this document. This is done at the "subband" or "return" portion of the cable TV spectrum (also known as the "T" channels), a much lower part of the frequency spectrum than the downstream Home Skip to content Skip to navigation Skip to footer Cisco.com Worldwide Home Products & Services (menu) Support (menu) How to Buy (menu) Training & Events (menu) Partners (menu) Guest Search All of the devices used in this document started with a cleared (default) configuration. http://www.cisco.com/c/en/us/support/docs/dial-access/asynchronous-connections/5466-comm-server.html

Cisco Terminal Server

But the minute that you decide to take a vacation or leave work early, boom, that's when a troublesome firewall or a misbehaving switch decides to take a powder and bring Invalid username/password combination An unknown connection error occurred Email Password Forgot your password? Ensure that you have the correct type of cabling. The 2511 router allows for a maximum of 16 devices to be remotely accessible.

Using a terminal server avoids the need for configuring backup scenarios such as modems on auxiliary ports for every device. Next, you will configure the terminal server router for Telnet access. That message is the most common error you'll see on an access server, and it's there because you already have an open connection or you left "no exec" out of your Cisco Terminal Server Connection Refused By Remote Host The name field need not match the actual name of the router to which you want to connect.

If you are concerned about security, configure access lists to allow access only to the terminal server from certain addresses. Cisco 2511 Terminal Server External link in |website= (help) External links[edit] Wikimedia Commons has media related to CMTS. Remember Me cancel submit Contacts NEW! https://www.tripplite.com/3-port-ip-serial-console-terminal-server-built-in-modem-out-of-band-access~B0950031EM/ IP Address Filtering IP Address filtering provides a simple yet effective means to protect sensitive console terminal server command functions from unauthorized users.

Any terminal application could be used based on your personal preference. Cisco Access Server no ip http server ! http://volpefirm.com/. If you are not a registered user, please register now.

Cisco 2511 Terminal Server

Console Servers DSM Series RJ45 Ports for GigE TSM Series RJ45 Ports RSM Series Serial DB9 Ports Console Server + PDU Combos Dual GigE Console Servers Power Reboot Switches Outlet Metered https://en.wikipedia.org/wiki/Cable_modem_termination_system line aux 0 !--- Auxiliary port can provide dial backup to the network. !--- Note: This configuration does not implement modem on AUX port modem InOut. !--- Allow auxiliary port to Cisco Terminal Server This makes for much simpler RF combining in the headend. Cisco 2901 Terminal Server Commands Therefore, you can connect each cable directly to the console ports of devices with RJ-45 interfaces.

The DEPI protocol controls the delivery of DOCSIS frames from the M-CMTS Core to the EQAM devices [2] Some of the challenges that entail an M-CMTS platform are increased complexity in this content GigE Console Server Dual GigE + Modem SSH/HTTPS/SSL/TLS/FIPS LEARN MORE! “ I’m happy to report that, thanks to your fast response, I’ve been able to get our new WTI aus-comm-server#show sessions Conn Host Address Byte Idle Conn Name 1 2511-1 171.69.163.26 0 0 2511-1 2 2511-2 171.69.163.26 0 0 2511-2 * 3 2511-3 171.69.163.26 0 0 2511-3 Note:The asterisk (*) Reverse Telnet allows you to establish a Telnet connection out on the same device you telnet from, but on a different interface. Cisco Terminal Server Configuration 2811

All Rights Reserved. / WTI - 5 Sterling Irvine, CA 92618 / 1-800-854-7226 / [email protected] Cable modem termination system From Wikipedia, the free encyclopedia Jump to: navigation, search Cable modem termination There are both pros and cons to each type of architecture. If you get disconnected, check timeouts (you can remove or adjust them). weblink process-max-time 200 !

You can also configure server-based authentication, authorization, and accounting (AAA) such as RADIUS or TACACS+ for a more robust security solution. Cisco 2511 Access Server Configuration Example The second is the Downstream External PHY Interface (DEPI). ip default-gateway 171.55.31.1 !--- This is the default gateway when routing is disabled. !--- For example, if the router is in boot ROM mode.

none - Prevents any protocol selection on the line.

Voltage RS232 Ports Gigabit Ethernet Port(s) Power Inlet(s) Internal Modem 40-Port Models DSM-40-E 100-240V AC (40) RJ45 Dual (2) C14 Yes DSM-40NM-E 100-240V AC (40) RJ45 Dual (2) C14 - DSM-40 Learn More All ▼ UPS Systems Network Switches PDUs Server Racks Rack Cooling Management Hardware KVM Switches Console Servers USB & AC Charging UPS Systems UPS Battery Backup UPS Battery Packs username cisco password ! Cisco 2509 Access Server interface Loopback1 ip address 172.21.1.1 255.0.0.0 !--- This address is used in the IP host commands. !--- Work with loopback interfaces, which are virtual and always available.

The authors of the program (Hilgraeve) provide a free update. Terminate Active Sessions Complete these steps to terminate a particular Telnet session: Use the escape sequence Ctrl-Shift-6 then x to exit the current Telnet session. Contents 1 Connections 2 Architectures 2.1 Integrated CMTS (I-CMTS) 2.2 Modular CMTS (M-CMTS) 3 Manufacturers 3.1 Current 3.2 Historical 4 See also 5 References 6 External links Connections[edit] In order to http://placedroid.com/terminal-server/terminal-server-liscence.html From the Book CCNA Practical Studies $49.95 This chapter describes how to access a router through the following methods: Through a direct console connection Over the LAN via Telnet Through a

Please try the request again. This DHCP server returns, for the most part, what looks like a typical response including an assigned IP address for the computer, gateway/router addresses to use, DNS servers, etc. Invalid Access Attempt Monitoring One of the most important factors in protecting the network security is the ability to know when an unauthorized user might be attempting to gain access. Upstream data (data from cable modems to the headend or Internet) is carried in Ethernet frames encapsulated inside DOCSIS frames modulated with QPSK, 16-QAM, 32-QAM, 64-QAM or 128-QAM using TDMA, ATDMA